Rane SIXTY-ONE Bedienungshandbuch

OWNER’S MANUALSIXTY-ONERANE SIXTY-ONE MIXER MANUAL

OWNER’S MANUAL10SIXTY-ONESixty-One Overview• Includes Serato DJ software. • Includes Rane ASIO and Core Audio Drivers for Serato DJ and other audio

OWNER’S MANUAL11SIXTY-ONESixty-One ConnectionsPower SupplyThis mixer features an internal universal switching power supply that operates on any AC mai

OWNER’S MANUAL12SIXTY-ONEUSB AudioThere are six stereo record channels and four stereo playback channels, plus a stereo channel for effects send from

OWNER’S MANUAL13SIXTY-ONEDeck Input ChannelsTwo Deck channels, or buses, have nearly identical controls with the exception of the Source selectors.Sou

OWNER’S MANUAL14SIXTY-ONEFilterThe FILTER sweeps from Low-Pass to High-Pass. Set to 12 o’clock for a at frequency response. Moving the lter toward t

OWNER’S MANUAL15SIXTY-ONEMic InputThis Mic input on a XLR/TRS combo jack has LEVEL, HIGH and LOW tone controls, FLEXFX assign and a meter. Select MIC

OWNER’S MANUAL16SIXTY-ONEFlexFxThe FlexFx Bus in the Sixty-One works differently than a typical effects insert loop. This architecture is very exible

OWNER’S MANUAL17SIXTY-ONERane DriversThe Serato DJ installer includes Core Audio (Mac) and ASIO (PC) drivers that allow your Rane Sixty-One to use oth

OWNER’S MANUAL18SIXTY-ONEDeck Inputs 1-2 Page Controls:Each Deck panel controls these functions:• Analog Input Source: Each input may be set to Line l

OWNER’S MANUAL19SIXTY-ONEMIDI MappingWhen using Serato DJ software, the mixer is plug-and-play with all required MIDI mapping done for you. For advanc

OWNER’S MANUAL2SIXTY-ONEATTENTION: RISQUE DE CHOCS ELECTRIQUE - NE PAS OUVRIRRISK OF ELECTRIC SHOCKDO NOT OPENCAUTIONTo reduce the risk of electrical

OWNER’S MANUAL20SIXTY-ONEMIDI ImplementationSerato DJ MIDI Control only supports:• Note On/Off• Standard 7-bit CC (Control Change)MIDI Note ON/OFF Cha

OWNER’S MANUAL21SIXTY-ONEMIDI Control Change ChartMIDI control changes initiated by the mixer are dedicated to mixer functions and read only. MIDI out

OWNER’S MANUAL22SIXTY-ONE78 0x4E Deck 2 Mid 0-127 0x00-0x7F82 0x52 Mic Low 0-127 0x00-0x7F83 0x53 Deck 1 Fader 0-127 0x00-0x7F84 0x54 Deck 2 Fader

OWNER’S MANUAL23SIXTY-ONEMagnetic Fader MaintenanceThe faders and crossfader in the Sixty-One are designed with materials highly resistant to corrosio

OWNER’S MANUAL24SIXTY-ONESensorsFader CalibrationAfter cleaning or replacement, the sensors may get moved, affecting the contour. After any fader serv

OWNER’S MANUAL25SIXTY-ONETechnical SpecificationsSixty-One SpecificationsAll specifications typical unless otherwise statedAnalog Inputs 4 Stereo unbalan

OWNER’S MANUAL26SIXTY-ONEDeclaration of ConformityApplication of Council Directives:2001/95/EC 2002/96/EC2004/108/EC 2006/95/EC2011/6 5/ EUManufa

OWNER’S MANUAL27SIXTY-ONELimited WarrantiesFactory Authorized ServiceYour unit may someday need to be serviced by the Rane Factory if you live in the

OWNER’S MANUAL28SIXTY-ONEWarranty Procedure - Valid in U.S.A. onlyNOTICE! You must complete and return the warranty card or register your product onli

OWNER’S MANUAL3SIXTY-ONEATTENTION: RISQUE DE CHOCS ELECTRIQUE - NE PAS OUVRIRRISK OF ELECTRIC SHOCKDO NOT OPENCAUTIONAn d’éviter tout risque de choc

OWNER’S MANUAL4SIXTY-ONECopyright Notices©2014 Rane Corporation. All rights reserved. Serato DJ and Scratch Live are trademarks of Serato. Trademarked

OWNER’S MANUAL5SIXTY-ONEContents2 Important Safety Instructions4 Check List6 Quick Start: Software6 Serato DJ Software Installation for Mac OSX6 Ser

OWNER’S MANUAL6SIXTY-ONEQuick Start: SoftwareBefore using your mixer, at least read this short section for the basics. Read the complete manual to get

OWNER’S MANUAL7SIXTY-ONEMAIN OUTPHONOGROUNDSANALOG INPUT SELECTSESSION100-240V 50/60 Hz 15 WATTSMADE IN U.S.A. RANE CORP.FLEXFX LOOPUSBOUTIN214

OWNER’S MANUAL8SIXTY-ONEAnalog Outputs• Main Out is on a pair of balanced ¼˝ TRS (tip-ring-sleeve) jacks.• Session Out is available on a pair of unbal

OWNER’S MANUAL9SIXTY-ONEHow To Calibrate Serato DJWith music playing in the background through your system or booth output, put your needle on the rec