Rane CP 52 1997 version Bedienungsanleitung PDF herunterladen

Manual-1

OPERATORS MANUAL CP 52

COMMERCIAL PROCESSOR

QUICK START

If you were the type that cheated on school book reports by just skimming through the reading assignments, then this

section is for you! It gives you not quite enough information to really know what you’re doing. But, if you follow the

recommended set up procedure, you should get at least a “B.”

Keep the amplifiers and the CP 52 turned off until all connections are made.

PAGE INPUT

Connect the PAGING INPUT to the Euroblock on the rear panel. On the front, select the appropriate MIC or LINE

switch position. Then set the gain with the PAGING TRIM control, then set the PAGING DETECT THRESHOLD and

finally the PAGING LEVEL. PHANTOM POWER, HIGH/LOW CUT FILTER and PAGE LEVEL TRACKS

ZONE LEVEL switches are located on the rear panel.

PROGRAM INPUTS

Connect line level program sources to the RCA PROGRAM INPUT jacks (LINE 1, 2, 3 & P). If you have a priority

program, like a jukebox, connect it to the PRIORITY Input. The Program PRIORITY assign switch turns priority

override ON or OFF. The Priority program is automatically selected when signal is detected at its Input. Set the

PROGRAM DETECT THRESHOLD and RELEASE TIME as desired.

ZONE EXPAND

Wire the ZONE EXPAND Output Euroblock as required to a mono feed delivering PAGE-only, PROGRAM-only or

ZONE (both) signal depending on the switch setting. This Output uses a cross-coupled line driver and may be used

balanced or unbalanced. Adjust the ZONE EXPAND LEVEL trim as desired.

ZONE OUTPUT

The ZONE OUTPUT uses a cross-coupled line driver and may be used balanced or unbalanced. Set the front panel

LIMIT THRESHOLD as required. Depress the MONO switch for a mono Zone.

ZR 1 REMOTE

You may use one ZR 1 Remote (sold separately) with the CP 52. Wire it to the ZONE REMOTE Euroblock as

indicated. If a ZR 1 remote is not used, any simple switch closure to GND will work for the D0 and D1 pins. These pins

are TTL compatible (0 to 5 VDC). The logic is inverse Gray Code. Any ground referenced 5 volt DC control may be used

as the input to Vc. Do not ground the Vr pin.

The CP 52 is very versatile. While this makes a large number of system applications possible, it also results in com-

plexity. For this reason, it is important to use an organized approach for setup and calibration. A highly recommended

setup procedure appears on page Manual-7. By following it you will encounter fewer problems and reduce the need to

increase our collective phone bills.

CAUTION: Never connect anything except an approved Rane Power supply to the thing that looks like a red

telephone jack on the rear of the CP 52. This is an 18 VAC center tapped power input. Consult the Rane factory for a

replacement or substitution.

WEAR PARTS: This product contains no wear parts.

1 2 3 4 5 6 7

Inhaltsverzeichnis

Seite 1 - OPERATORS MANUAL CP 52

Manual-1OPERATORS MANUAL CP 52COMMERCIAL PROCESSORQUICK STARTIf you were the type that cheated on school book reports by just skimming through the rea

Seite 2 - CP 52 - FRONT PANEL

Manual-2CP 52 - FRONT PANEL햲 PAGING TRIM control adjusts the Page Input preamplifier gain to match the microphone/source in use, not to set the Pagele

Seite 3 - CP 52 - REAR PANEL

Manual-3CP 52 - REAR PANEL햲 Chassis Ground Screw provides a convenient earth (technical) ground connection point. The CP 52 does not ground thechassis

Seite 4 - CP 52 CONNECTION

Manual-4CP 52 CONNECTIONBe sure the power to the CP 52 is OFF until allconnections are made.EUROBLOCK CONNECTIONSAll Input and Output connections are

Seite 5 - ZR 1 REMOTE INSTALLATION

Manual-5ZR 1 Program Select/Level Remote ControlZR 1 REMOTE INSTALLATIONThe CP 52 supports a wired remote for Zone Level andZone Source selection. Wir

Seite 6 - Manual-6

Manual-6RECOMMENDED CALIBRATION PROCEDUREThe CP 52 is a very versatile instrument. While this allows it to conform to the requirements of a large numb

Seite 7 - Manual-7

Manual-7©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)355-6000 FAX (425)347-7757 WEB http://www.rane.comCALIBRATION1. Con

Kommentare zu diesen Handbüchern

Keine Kommentare

Rane CP 52 1997 version Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio Rane CP 52 1997 version herunter. Rane CP 52 1997 version User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audio Rane CP 52 1997 version