Rane ECM 64 Bedienungsanleitung

Manual-1OPERATORS MANUAL ECM 64CONFERENCE SYSTEMQuick StartThe ECM 64 is a very versatile product with many applications. This section will help you

Manual-10ECM 64 Input and Output ControlsInputsEach Input has programmable Trim and Mute controls. TheInput Trim operates from –15 to +16 dB in 1 dB s

Manual-11Digital Hybrid ControlsPeripheral Status and Dial DialogsDigital HybridThe DH 1 Digital Hybrid is an optional module, includedin the ECM 64A

Manual-12Alignment ProcedureQuick Overviewa. Setup Mic gainsb. Setup Line In and Aux In Input levelsc. Select matrix routing and if necessary the matr

Manual-13DH 1 and ECA 1 InstallationECA 1DH 1ECM 64 OptionsTwo internal cards are available for the ECM 64. TheECM 64AD already includes both options.

Manual-14Advanced ApplicationConnecting the ECM 64 to a larger ECSIn this application the system required:• Full duplex audio for a Video Codec and

Manual-15ECM 64 and Larger ECS Installation

Manual-16Device Control LanguageData StructuresAbbreviations used: Definition:$: signifies hexadecimal numberADDR: Device AddressCHNUM: Channel Number

Manual-17Output 1 Parameters:Index Hex Name / System ParametersEncoding Method33 $21 Output (Mute)* 1/0 (byte) 1 = Mute34 $22 Output Level 0 to 118

Manual-18Device Type (DT):$32 = ECM 64Manufacture’s Identification code (ID):$08 = Rane CorporationChannel Number codes (CHNUM):Typically set to 0, un

Manual-19Program all channels from memory on all devices (82 hex):Transmit $FB 00 $FB 00Transmit $00 $03 (where $03 = number of data bytes to follow i

Manual-2Front Panel Description INPUT SIG and OL level indicators: SIG lights when the Input signal (before trim) is above –25 dBu for Mics and –19dB

Manual-20Send Globals (8C hex):Transmit ADDR header ($FB XX $FB XX, where XX = ADDR) (See Note 9)Get DTGet IDTransmit $00 $72 (where $72 = number of

Manual-21Hybrid Parameter List (HPL)Hybrid Command Data Description0 Dial DTMF Number (char) string Null terminated ASCII string, 20 (char) max1 Dial

Manual-22STATUS consist of 20 bytes returned in this order:Byte Parameter Value1 OPSTAT See OPSTAT2 Preset Memory 1 - 163 Working/Stored Flag 1/0 (See

Manual-23Get Device Serial/Identification Number (04 hex):Transmit ADDR header ($FB XX $FB XX, where XX = ADDR) (See Note 9)Get DTGet IDTransmit $00

Manual-24Notes1. When the value $FB occurs anywhere except in an ADDR header, it is repeated.2. The data size is the number of bytes, prior to the $FB

Manual-25Example Packet Expansion Code for RW 232 Messages// 09-10-96 - Devin Cook (Derived from RW232.CPP code)// This code only deals with the Body

Manual-26Compliance NoticesFCC NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

Manual-3Rear Panel Description Chassis ground point: A #6-32 screw is supplied for chassis grounding purposes. Although the RS 3 supplies a third wir

Manual-4Typical ECM 64AD InstallationThe ECM 64AD is preprogrammed to operate out of thebox using the following system configuration. Run RaneWare,cho

Manual-5Wiring Digram for Typical ECM 64AD InstallationAP1.C64 RaneWare Screens

Manual-6Site SurveyBefore you start any installation, be aware of thesequidelines. For the ECM 64 to operate properly the followingmust be closely ob

Manual-7Rane does not supply an external control device to operatethe ECM 64. Custom wiring recommendations:• Use momentary or toggle-type switches

Manual-8Software OperationOverviewRaneWare controls and commands will be in Sans-seriftype like this and match the defaults shown in RaneWare. Beawar

Manual-9After Polling, the Device Selection window displays anyconnected RW 232 units, as well as Offline versions of allRane RW 232 products.The quic