Rane MLM 82 1997 version Bedienungsanleitung PDF herunterladen

Manual-1

MLM 82

MIC/LINE MIXER

OPERATORS MANUAL

MLM 82 CONNECTION

When connecting the MLM 82 to other components in

your system for the first time, leave the power supply for last.

This gives you a chance to make mistakes and correct them

without damage to your fragile speakers, ears and nerves.

INPUTS

The sixteen jacks at the Inputs of the MLM 82 are

balanced. They will also accept unbalanced connectors. Use

only shielded cable for Inputs. For best noise rejection use

two-conductor-plus-shielded wire, even for unbalanced

operation. Connect the shield at both ends to help insure

proper grounding. See the Sound System Interconnection

RaneNote included with this manual for all cable adaptations.

MONO INPUTS 1-4. Connect up to 4 sources to these

XLR jacks. Rane follows the AES recommended practice of

pin 2 postive, pin 3 negative, and pin 1 to shield. Switch any

Input connected to a microphone to the mic position by the

associated “limited access” switches on the front panel (LED

off). When connecting line level signals, switch the input to

the LINE position (LED on). Use a small probe such as a #0

Phillips screwdriver to actuate the switch.

STEREO INPUTS 5-8. The ¼" connectors are line level

stereo/mono balanced/unbalanced Inputs. If the MLM 82 is to

be used with unbalanced sources (such as CD players),

QUICK START

This section is provided as a convenience for those in a rush. If you are experienced with this unit or other Rane

products, these few words will refresh your memory.

INPUTS 1 through 4 may be microphone or line level. The choice between the two is made by setting the LINE push-

buttons through the access holes on the front of the unit near the INPUT LEVELS. Follow the silk-screening on the rear

for proper wiring hookup.

Choose between MIC or LINE output levels at each of the XLR OUTPUT connectors. If the MLM 82 is connected

directly to a power amplifier, equalizer or recorder input, choose LINE level. If the MLM 82 is connected to a microphone

jack of an existing sound system, choose MIC level. Follow the silk-screening on the rear for proper wiring hookup.

Once Inputs, Outputs, and power are properly connected, with the OUTPUT LEVELS counterclockwise (off), set the

Input LEVELS as high as possible without causing the SIG/OL indicators to blink red more than occasionally during

extreme signal peaks. Now slowly raise the OUTPUT LEVELS as desired.

Never connect anything except an approved Rane power supply to the red thing that looks like a telephone jack on

the rear of the MLM 82. This is an AC input and requires special attention if you do not have a power supply exactly like

the one that was originally packed with your unit. See the full explanation of the power supply requirements on page

Manual-3.

consult the Sound System Interconnection RaneNote included

with this manual for proper wiring using ¼" TRS input

connectors. Stereo Inputs use both RIGHT and LEFT jacks at

each INPUT.

INPUTS 5 through 8 also serve as mono Inputs by either

using the XLR inputs (always mono) or by plugging into only

one of the ¼" jacks. Automatic switching occurs when only

one of these ¼" jacks are used at any Input, splitting the mono

signal to both Outputs. Connect to just one of these jacks and

the MLM 82 does the rest. If you only want the signal to

come out of one channel and not the other, plug an unwired

“dummy” ¼" plug into the other channel.

OUTPUTS

The MLM 82’s OUTPUTS are balanced. The same wiring

conventions as the XLR Inputs apply. The type of device

following the MLM 82 must be considered when setting the

Output Level switch. Choose between LINE (0 dB) or MIC

(-40 dB) output levels. If the MLM 82 is connected directly to

a power amplifier input, choose LINE level. If the MLM 82 is

connected to a microphone jack on an existing sound system,

choose MIC level. For unbalanced OUTPUT connections do

not tie pin 3 (i.e. “–”) to ground.

WEAR PARTS: This product contains no wear parts.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - OPERATORS MANUAL

Manual-1MLM 82MIC/LINE MIXEROPERATORS MANUALMLM 82 CONNECTIONWhen connecting the MLM 82 to other components inyour system for the first time, leave th

Seite 2 - FRONT PANEL DESCRIPTION

Manual-2FRONT PANEL DESCRIPTION햲 SIGnal present/OverLoad LED. This bi-color LED lights green for a -30 dBu signal, and turns red when the Input iswit

Seite 3 - REAR PANEL DESCRIPTION

Manual-3REAR PANEL DESCRIPTION햲 MIC/LINE INPUT jacks 1-4. These XLRs connect either balanced Microphone or Line signals, depending on the recessedfron

Seite 4 - OPERATING INSTRUCTIONS

Manual-4©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)-355-6000 FAX (425)-347-7757 WEB http://www.rane.comOPERATING INSTR

Kommentare zu diesen Handbüchern

Keine Kommentare

Rane MLM 82 1997 version Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio Rane MLM 82 1997 version herunter. Rane MLM 82 1997 version User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audio Rane MLM 82 1997 version