Rane SAC 22 2001 version Bedienungsanleitung PDF herunterladen

Manual-1

QUICK START

Whoa, hold on there. Even if you don’t read manuals as a matter of principle, at least read this section to avoid hurting

yourself or your equipment.

Connect the SAC 22 with the power off. Balanced XLR cables are recommended, but if you must convert to ¼" connec-

tors, buy or make a cable like the ones on page Manual-11 and keep them as short as possible. This device uses low imped-

ance balanced line drivers. Do not connect the “+” or “–” output pins to ground, as this may cause the power supply to

shut down. For unbalanced use, leave the unused output pin (“+” or “–”) unterminated.

Consult the speaker manufacturer for the correct crossover FREQUENCY setting. As rugged as some drivers are, many

(especially compression drivers) will not accept frequencies outside of their normal range without producing distortion and

possibly self-destruction.

With all equipment turned off and LEVEL controls down, begin making connections to the system as shown on page

Manual-4 or 5. When turning on the system, switch on the power amplifiers last. Now, feed the SAC 22 some program

material. Start by turning up the LOW LEVEL and HIGH LEVEL to the 0 dB marks. Slowly increase the INPUT

LEVEL, even if it goes all the way to 10, so the +4 dBu (green) light blinks occasionally and the OL (red) light stays out.

This delivers the best signal-to-noise performance.

The MONO SUB OUTPUT is a sum of the Left and Right Low Outputs. The MONO SUB LEVEL adjusts only this

Output and is not affected by the LOW LEVEL control.. When using a single subwoofer along with full-range cabinets

that have internal crossovers, set the 100 Hz FILTER to OUT, allowing the front panel FREQUENCY to control the

subwoofer crossover point. When used with biamp cabinets and a subwoofer, set the 100 Hz FILTER switch to IN to allow

only frequencies below 100 Hz at this output jack. This way, the SAC 22 almost does the job of a Stereo 3-Way crossover,

but without removing that awesome bass from the Left and Right Low Outputs.

WEAR PARTS: This product contains no wear parts.

OPERATORS MANUAL SAC 22

STEREO 2-WAY ACTIVE CROSSOVER

1 2 3 4 5 6 7

Inhaltsverzeichnis

Seite 1

Manual-1QUICK STARTWhoa, hold on there. Even if you don’t read manuals as a matter of principle, at least read this section to avoid hurtingyourself o

Seite 2 - IMPORTANT SAFETY INSTRUCTIONS

RISK OF ELECTRIC SHOCKDO NOT OPENCAUTIONTo reduce the risk of electrical shock, do not open the unit. No user serviceable parts inside. Refer servicin

Seite 3 - Manual-2

Manual-2INPUT LEVEL control and indica-torsThis controls the overall levelwithout altering the relative settings ofthe Low and High frequency Outputs.

Seite 4 - Manual-3

Manual-3Power ON switch and LEDYour basic, straightforward powerswitch. When the yellow LED is lit, theSAC 22 is ready to go.LOW/HIGH FREQUENCY contro

Seite 5 - Manual-4

Manual-4APPLICATION — ACTIVE 2-WAY WITH (or without) MONO SUBUse this configuration if you have separate speaker inputs for the low and high drivers,

Seite 6 - OPERATING INSTRUCTIONS

Manual-5Setting the Output Level ControlsThe INPUT LEVEL is an overall system sensitivityadjustment. Use this control to decrease the overall sensitiv

Seite 7 - Manual-6

Manual-6©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)355-6000 FAX (425)347-7757 WEB http://www.rane.com104967Setting the

Kommentare zu diesen Handbüchern

Keine Kommentare

Rane SAC 22 2001 version Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio Rane SAC 22 2001 version herunter. Rane SAC 22 2001 version User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audio Rane SAC 22 2001 version