Rane AC 23S Betriebsanleitung PDF herunterladen

Manual-1

AC 23S

ACTIVE CROSSOVER

OPERATORS MANUAL

WEAR PARTS: is product contains no wear parts.

MONO 4W OR 5W: INACTIVE 4W: INACTIVE4W: INACTIVE

100

MAXMIN

10 0

80 900

850

15 0

200

240

75 0

600

400

19 0

250

7 . 0k

5.8k

550

47 5

350

70 0

2.0k

2.8k

4. 5k

1.0k

19 0

250

7 . 0k

5. 8k

550

47 5

350

70 0

2.0k

2.8k

4. 5k

1.0k

1k70

4W: MID / HIGH

2W: INACTIVE 2W: INACTIVE 2W: LOW / HIGH 2W: LOW / HIGH2W: INACTIVE2W: INACTIVE 2W: LOW2W: LOW

10 0

80 900

850

15 0

200

240

75 0

600

400

1k70

MUTE

LEVEL LEVEL LEVEL LEVEL

MASTER

LEVEL

MASTER

LEVEL LEVEL LEVEL

MUTE

FREQUENCY

DELAY DELAY DELAY DELAY

FREQUENCY FREQUENCY

MUTE MUTE

AC 23S

ACTIVE

CROSSOVER

CH 2CH 1

FREQUENCY

LOW MID LOW MIDHIGH HIGH

MIDMONO MASTER SUBWOOFER SUB / LOW HIGHLOW LOW / MID

MID / HIGHLOW / MID MID / HIGHLOW / MID

5W: HIGH-MID / HIGH5W: HIGH-MID5W: MID / HIGH-MID

POWER

QUICK START

Labels above the controls refer to the unit being operated in the

2- or 3-Way Stereo mode. Labels below the controls refer to the

unit being operated in the 4- or 5-Way Mono mode.

Set the STEREO/MONO switch appropriately. e fact that

the AC 23S is a multiple function unit means the outputs are

switched around in Mono mode.

To operate the unit in Stereo 3-Way mode, be sure the rear

panel switches are set for STEREO 3-Way, and the 4W / 5W

switch is set for 5-Way. Following the labels above the controls

and jacks in logical order, you will ﬁnd Channel 1 Master Input

LEVEL, LOW Output, MID Output, and HIGH Output, with

the same for Channel 2. If you need a summed Mono Low Ou-

put, see ‘Monoing the Low Outputs’ on page Manual-15.

To use the unit as a Mono 5-Way, ﬁrst check that the Chan-

nel 1 and 2 switches are set to 3-WAY, and the push-switch is

depressed for MONO. Connect the INPUT source to Channel 1

only. Following the labels below the jacks, look at SUB OUT,

then look over at LOW OUT, now go back to MID OUT, then

over to HIGH-MID OUT and then proceed to the HIGH

OUT.

ere are two diﬀerent conﬁgurations for Mono 4-Way

systems. If your LOW / MID can use a crossover frequency

between 70 Hz-1 kHz, see page Manual-7. If your LOW / MID

prefers a higher range of 190 Hz-7 kHz, see page Manual-8.

In agreement with IEC and AES/ANSI standards, AC 23S

wiring convention is pin 2 Positive, pin 3 Negative (return),

pin 1 to chassis ground. See the “Sound System Interconnection”

RaneNote included with this manual for more information on

cabling and grounding requirements.

1 2 3 4 5 6 ... 14 15

Inhaltsverzeichnis

Seite 1 - OPERATORS MANUAL

Manual-1AC 23SACTIVE CROSSOVEROPERATORS MANUALWEAR PARTS: is product contains no wear parts.MONO 4W OR 5W: INACTIVE 4W: INACTIVE4W: INACTIVE100248610

Seite 2 - *Not used for 2‑channel 2‑way

Manual-10Time Delay Adjustment Using Realtime Analyzer & Pink Noiseis method outlines the use of a realtime analyzer, pink noise generator and ﬂa

Seite 3 - Manual-3

Manual-11Time Delay Adjustment Using SPL Meter & Tone GeneratorNow that good quality realtime analyzers are becoming more af-fordable and easier t

Seite 4 - 1345 6789 0q2345 6789 0qw

Manual-12 Voice Coil Displacement (Inches)(Hz) .75" 1.5" 3" 6" 9" 12" 15" 18" 21&

Seite 5 - Manual-5

Manual-13Setting the Output Level ControlsChoosing the crossover frequencies was the easy part. Now it gets real fun. e idea is to set the output Lev

Seite 6 - 1234 50qw e678 9rty uio

Manual-14Setting Levels Using an SPL Meter & Pink Noise Generatore MUTE switches on the AC 23S make using an SPL meter an easy and relatively acc

Seite 7 - Manual-7

Manual-15Constant Directivity Horn EQ ModConstant Directivity (or CD) horns need additional equaliza-tion to help cover the same area a long throw hor

Seite 8 - Manual-8

Manual-2FRONT PANEL: STEREO 2-WAY CONFIGURATIONObserve the labels above the controls for stereo operation.*Not used for 2‑channel 2‑way1 Channel 1 MAS

Seite 9

Manual-3REAR PANEL: STEREO 2-WAY CONNECTIONSObserve the labels above the Inputs and Outputs for Stereo operation. 1 CHANNEL 1 INPUT: Plug the left out

Seite 10 - Time Delay Adjustment Using

Manual-4FRONT PANEL: STEREO 3-WAY CONFIGURATIONObserve the labels screened above the controls for stereo operation.1 Channel 1 MASTER LEVEL control: S

Seite 11 - Meter & Tone Generator

Manual-5REAR PANEL: STEREO 3-WAY CONNECTIONSObserve the labels above the Inputs and Outputs for Stereo operation.1 CHANNEL 1 INPUT: Plug the left outp

Seite 12

Manual-6FRONT PANEL: MONO 4-WAY AND 5-WAY CONFIGURATIONMONO 4W OR 5W: INACTIVE 4W: INACTIVE4W: INACTIVE10024861002486100248610024861002486100248610024

Seite 13 - Analyzer

Manual-7REAR PANEL: MONO 4-WAY AND MONO 5-WAY CONNECTIONSObserve the labels below the Inputs and Outputs for Mono operation.1 MONO INPUT: Connect the

Seite 14 - Setting Levels Using an SPL

Manual-8REAR PANEL: ALTERNATE MONO 4-WAY CONNECTIONSThe switching in the AC 23S will result in a Mono 4‑Way conguration with the crossover ranges SUB

Seite 15 - Monoing the Low Outputs

Manual-9OPERATING INSTRUCTIONSSelecting Crossover FrequenciesMost speaker manufacturers supply low and/or high frequency cut-oﬀ points for each driver

Weitere Dokumente für Prozessoren Rane AC 23S

Um das Dokument anzuzeigen Rane AC 23S Betriebsanleitung

Rane AC 23S Betriebsanleitung (18 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Rane AC 23S Betriebsanleitung

Stöbern Sie online oder laden Sie Betriebsanleitung nach Prozessoren Rane AC 23S herunter. Rane AC 23S Operating instructions Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Prozessoren Rane AC 23S

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Prozessoren Rane AC 23S