Rane MM 12 Bedienungshandbuch PDF herunterladen (Seite 20)

OWNER’S MANUAL

SIXTY-FOUR

Effects Parameter Table

Effect Depth Knob Time Encoder Tap Button Beat Joystick Shift or Control

Panel Option*

Filter

Adjusts the strength of

the effect.

Adjusts the LFO time

independent of the

current BPM and Beat

Multiplier.

Holding down the

Shift button and

turning the Time

encoder adjusts the

BPM.

Pressing the Time

encoder re-syncs the

effect.

The Tap button

manually enters a

new BPM.

A minimum of two

taps is required to

get a new BPM.

The mixer can sync

these effects to

different sources.

See "Effects

Synchronization"

on page 19.

Adjusts the BPM

multiplier to change

the number of bars.

Up increases the

multiplier and down

decreases the

multiplier.

Available multiplier

values are: 1/16, 1/8,

1/4, 1/2, 3/4, 1/1, 2/1

4/1, 8/1, 16/1, 32/1

and 64/1. (64/1 not

available in Echo).

Press down on the

Beat joystick to Lock

the current BPM. This

prevents the current

BPM from changing

until you manually

change the BPM,

Time, BPM Clock

Source, or click the

Beat Joystick button

again to unlock

it. Locked BPM is

indicated by “BPM”

ashing in the display.

• High-pass Filter with

low frequency point

sync.

• Low-pass Filter with

high frequency point

sync.

Flanger

• Flanger with positive

feedback.

• Flanger with negative

feedback.

Phaser

None

Echo

Adjusts the amount

of echo recirculation,

which in turn affects

how quickly the echo

effect decays. The

amount of recirculation

varies with the echo

options selected (see

last column). Setting

the control to minimum

or “0” results in a

Dry signal with the

minimum recirculation

setting. Setting the

control to maximum

or “10” results a Wet

signal with maximum

recirculation.

Adjusts the length of

the recorded sample

used by the echo.

Holding down the

Shift button and

turning the Time

encoder adjusts the

BPM.

Pressing the Echo

button clears the

echo. Time range is 1

ms to 10920 ms.

• Echo: No feedback

lter. Recirculation is

adjustable 0-70%.

• Hold Echo: No

feedback lter.

Recirculation is

adjustable 0-100%.

• Low-cut Echo:

Feedback lter

adjustable from

20 Hz to 10 kHz.

Recirculation is

adjustable 0-70%.

• Low-cut Hold Echo:

Feedback lter

adjustable from

20 Hz to 10 kHz.

Recirculation is

adjustable 0-100%.

When either Hold Echo option is selected, it is possible to suspend an echo. To engage

suspend, press the Time encoder. The Echo button ashes, indicating that suspend is

active. Suspend terminates input to the delay memory while continuing to play delay memory

indenitely. Press the Time encoder again to terminate suspend. If you want a suspended echo

to gradually decay, turn the Depth knob CCW. If you want the decay to stop, turn the Depth

knob back to or above where it was at when suspend was engaged.

Robot

Adjusts the wet/dry

mix and warble of the

robot.

Adjusts the % of pitch

shift, shown by the

bar in the display.

Pressing the Time

encoder resets pitch

shift to 0%.

Does not affect the

robot.

Adjusts the pitch up/

right or down/left in

20% steps.

None

Reverb

Adjusts reverb

intensity.

Adjusts the % of

reverb decay time,

shown by the bar in

the display.

Does not affect

reverb.

Adjusts the decay

time up/right or down/

left in 10% steps.

*Effect options

available in the "Shift

Options" on page 23

or in the "Driver Control

Panel" on page 26.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare

Rane MM 12 Bedienungshandbuch Seite 20

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für DJ-Controller Rane MM 12