Rane SR 2 Bedienungsanleitung Seite 1

SR 2SMART REMOTECONTENTSQuick Start 2Front Panel Description 3Rear Panel Description 4Working with Smart Remotes 5SR 2 Wiring Guidelines 10SR 2 C

Manual-10SR 2 Wiring GuidelinesRestrictions24 AWG CAT 5 cable resistance = 26 ohms per 1,000 feet. ere are two wir-ing restrictions. First, RW 485 ha

Manual-1112 to 15 VDCregulatedpowersupply:Radio Shack273-1691or equivalent.Radio Shack273-1641AdaptaplugTIPREMOTE INTERFACE PORTTo more SR RemotesRPM

Manual-12REGULATEDPOWERSUPPLYSingle Run Distance (Series)Multiple Run Distances (Star)REMOTE INTERFACE PORTRPMAB+V-V(RW 485)REGULATEDPOWERSUPPLYREMOTE

Manual-13Cable Type 12 twisted pair unshielded CAT 5, Belden #1588(A,R)2 twisted pair unshielded CAT 5, Belden #1590ANote: This table is only for syst

Manual-14S R S R S RE NCOD ER LOC KRA NE CO R P.MAD E IN U.S.A .RE MO TE INTER FAC EPO RT ( RI P )ADD R ES S-V+VA BMAD E IN U.S.A .RA NE CO R P.

Manual-15Cable Type 24 twisted pair unshielded CAT 5, Belden #1583(A, B, E, ENH, R)4 twisted pair shielded CAT 5, Belden #1624 (P, R)4 twisted pair u

Manual-16Cable Type 24 twisted pair unshielded CAT 5, Belden #1583(A, B, E, ENH, R)4 twisted pair shielded CAT 5, Belden #1624 (P, R)4 twisted pair u

Manual-17Cable Type 2More conductors mean greater operating distance.Multiple run restriction (per table entries): d1 ≤1,000 ft, d2 ≤1,000 ft, d3 ≤1,0

Manual-18SR 2 Communication Protocole SR 2 communication protocol follows Rane’s RW 485 specication. e follow-ing describes the SR 2 implementation

Manual-19<msgtype> e msgtype is a one byte set of ags indicating options, bit 7=MSB: bit 0) set = checksum is valid bit 1) set = there h

Manual-2SR 2SMART REMOTE OPERATORS MANUALQuick StartWho would guess that a little box with one knob could have such a thick manual? At least read this

Manual-20e SR 2 responds with response data based on the commands/arguments it was sent. e SR 2 limits its response data to 40 characters. In the ca

Manual-21Conguration CommandsVGet Firmware, Hardware Version Send: V Response: n1,n2,"OK" Where: n1 is a two digit ASCII encoded dec

Manual-22To write a stored parameter value: Send: SPL,n1,n2 Where: n1 is the stored parameter index. n2 is the value to be stored. Exampl

Manual-23To write the Software Input Lock status: Send: ILK,n1 Where: n1 is the Software Input Lock byte. e lock byte range is [0, 7].

Manual-24ISInput SuggestSuggests new main level and second level. Resets the command state to No Operation.If Auto Level is enabled, the main level is

Manual-25ISRInput Suggest RawSame operation as IS Input Suggest except ISR returns the command state byte and button time. Suggests new main level and

Manual-26IFInput ForceForces new main level and second level. Resets the command state to No Operation.e main level is updated and indicated by the L

Manual-27Stored Parameter List (SPL)Below is a table of stored parameters followed by descriptions of each parameter.Index Description Values Setting

Manual-28Parameter Specication Limit Units Conditions/CommentsI/O: Type RS-485 Euroblock connector...Impedance 12k min Ω Receive Mode...

Manual-29Parameter Specication Limit Units Conditions/CommentsI/O: Type RS-485 Euroblock connector...Impedance 12k min Ω Receive Mode...

Manual-3Front Panel Description1 Colored insert (4 colors included).2 Clear lens helps support dif-ferent color templates which mount behind the lens.

Manual-30WarrantyFactory Authorized ServiceYour unit may be serviced by the Rane Factory or any Authorized Rane Service Center. To nd a Service Cente

Manual-31LIMITED WARRANTY OUTSIDE THE U.S.A.RANE PRODUCTS ARE WARRANTED ONLY IN THE COUNTRY WHERE PURCHASED, THROUGH THE AUTHORIZED RANE DISTRIB

Manual-32Warranty Procedure - Valid in USA onlyNOTICE! You must complete and return the warranty card or register your product online to extend the Wa

Manual-33FACTORY SERVICEIf you wish your Rane product to be serviced at the factory, it must be shipped fully insured, in the original packing box or

Manual-34Declaration of ConformityApplication of Council directive(s):73/23/EEC 89/336/EEC Manufacturer:Rane Corporation10802 47th Avenue WestMukilte

(Signature)November1, 2001(Date)Mukilteo WA USA(Place)Compliance Engineer(Position)Roy G. Gill(Full Name)Declaration of ConformityApplication of Coun

SR 2SMART REMOTE0.15"0.7"1.95"1.4"1.7"4.1"3.8"3.25"02716543ACN.001.345.482 RANE CORP.REMOTE INTERFACEPORTMADE

Manual-4Rear Panel Description1 6-wire Euroblock connector. Connects the SR 2 to a controller. A con-nects to RS-485 data +, B connects to RS-485 data

Manual-5Working with Smart RemotesSmart Remote OverviewSmart Remotes are congured within Drag Net 4 and higher. e follow-ing sections describe cong

Manual-6SR 2 Conguration Parameterse SR 2 features a 31-position LED indicator and rotary data encoder with integrated push switch. e push switch p

Manual-7Baud Ratee Baud Rate can only be set when Serial Mode is selected during polling. When conguring Remotes used with Rane controllers (i.e., R

Manual-8Live to StorageImportant: Transferring from a Live remote to an existing Storage congura-tion overwrites the Storage conguration. To transfe

Manual-9Updating Smart Remote FirmwareIt may be necessary to update a Smart Remote’s rmware in order to add features or address one of those pesky gl